skip to main content

I want to...

Current filter:

Rubbish & Recycling Rubbish & Recycling

Wood burners (fireplaces) and swimming pool fencing

Wood burnersWood burners

Rules governing fireplaces are designed for keep people safe and to protect the environment. Fireplaces are one of the oldest ways of heating homes but there are significant safety issues associated with their installation, so regulations exist to minimise potential risk to your family.

Installing a fireplace

You must get a Building Consent before installing any fireplace. This helps to ensure the fireplace meets all safety standards.

If you are planning to install a new residential solid fuel fire, you need to fill out and lodge the online Building Consent/PIM Form 2 application form.

Building Consent/PIM Form 2 online application

The application requires the following documentation:

  • A full plan of the house showing the location of the burner, sleeping areas, smoke alarms and any sleep-out on the property.
  • A copy of the fireplace manufacturer’s specifications and installation instructions for the fire and flue (second hand fires or flues are NOT permitted).
  • Details of the proposed flashing of flues (including any alternative solution).
  • If the application includes a wet-back, a plumbing specification and schematic drawing for the hot water cylinder, wet-back and tempering valve. Note: All plumbing work must be completed by a registered plumber.
  • Approved smoke detectors with hush buttons must be installed in or within three metres of each sleeping space and in the escape routes on all levels within the household unit.

Ensure that you apply for a Code Compliance Certificate (CCC) once the installation is complete (see below). 

What will the Building Consent cost?

Solid Fuel Heater applications have a fixed fee which allows for one inspection during installation. Additional inspections, if required, will cost extra;  see: Council's Fees and Charges page - Solid Fuel heaters.

What type of solid fuel heater can you install or use?

Council can only approve Building Consent applications for models of solid fuel heaters that have been tested by the Ministry for the Environment. For the full list of tested fires, including brands, models and emission rates, see: Ministry for the Environment.

The heater must comply with the National Environmental Standards for air quality if it is installed on properties of less than 2ha.

Hawke’s Bay Regional Council (which oversees air quality in Hawke’s Bay) has set limits on fireplace emissions within the areas worst affected by air pollution. These areas are called “Air Sheds”. For more information see: Hawke's Bay Regional Council or phone the regional council on +64 6 835 9200. For a map of the Hastings' air shed see the Hawke's Bay Regional Council website.

Old and existing fireplaces

Hawke's Bay Regional Council has set rules that ban certain types of non-complying fires and older fires from being used. These models will need to be replaced with a complying model or alternative heating system. For more information on the types of fires that can and cannot be used see the Hawke's Bay Regional Council website.

Inspections

All solid fuel heater installations must be inspected by a Hastings District Council building inspector.

For insert fires (into an existing chimney including those with a wetback), the officer will need to carry out the inspection during the installation of the heater in order to inspect the prepared chimney, any wetback and hot water cylinder components, and the final installation position of the fire.

For free-standing fires (including those with a wetback), the officer will need to carry out the inspection on the completion of the installation.

To book an inspection phone, Council.

If your inspection fails, Council will need to re-inspect the installation and you will be invoiced for additional inspections.

Final step: Code Compliance Certificate

When the installation has been passed, you must complete an application for a Code Compliance Certificate. The building officer who carries out your inspection will provide you with this form. On receiving your signed Application for Code Compliance Certificate, Council will issue your Code Compliance Certificate (subject to any additional fees being paid and/or documentation required).

NOTE: Do not use (light) your fire until Council’s building officer has passed the final inspection and you have applied for and obtained your Code Compliance Certificate.

Using your fire without a Code Compliance Certificate may invalidate an insurance claim related to the heater.

For more information see Council's Code Compliance Certificate page.

Loading...

Hastings District Council - Copyright © 2024 Hastings District Council

Disclaimers and Copyright
While every endeavour has been taken by the Hastings District Council to ensure that the information on this website is accurate and up to date, Hastings District Council shall not be liable for any loss suffered through the use, directly or indirectly, of information on this website. Information contained has been assembled in good faith. Some of the information available in this site is from the New Zealand Public domain and supplied by relevant government agencies. Hastings District Council cannot accept any liability for its accuracy or content. Portions of the information and material on this site, including data, pages, documents, online graphics and images are protected by copyright, unless specifically notified to the contrary. Externally sourced information or material is copyright to the respective provider.

© Hastings District Council - / +64 6 871 5000 / customerservice@hdc.govt.nz